Effect of Enameling on the Strength and Dynamic Fatigue of Soda–Lime–Silica Float Glass

The effect of a glass enamel coating on the strength and fatigue behavior of float glass was investigated. Commercially available enamel that was comprised of Cu₂Cr₂O₄ pigment particles in a bismuth-zinc borosilicate glass matrix was applied to a soda–lime–silica float glass via screen printing, followed by fusion at elevated temperature. Strengths of the enameled specimens were evaluated in biaxial flexure using a ring-on-ring (ROR) test geometry, and the data were analyzed using a conventional two-parameter Weibull distribution. Enameling was found to significantly degrade the strength of the float glass. There was no statistical difference in the characteristic strengths of samples enameled on the air side (66 MPa) compared with samples enameled on the tin side (61 MPa) of the float glass. Fractographic analysis revealed that the failures in the enameled float glass samples initiated at pores and pigment aggregates in the enamel, whereas failures in float glass samples initiated solely from surface flaws. Dynamic fatigue tests were performed on enameled float glass and indented float glass samples to determine the effect of the enamel on the stress corrosion behavior of the enameled components. There was no statistically significant difference between the stress corrosion exponents for the float glass and enameled float glass specimens.     

Formation of hydrophilic starch coatings on polyethylene films

Thin starch coatings were deposited onto polyethylene (PE) film surfaces when PE films were immersed in 1% jet cooked starch solutions and the hot solutions were allowed to cool. Normal cornstarch, waxy cornstarch, high amylose cornstarch, and solvent‐extracted normal cornstarch (to remove native lipid) were used in these experiments. Amounts of adsorbed starch varied from about 0.03–0.05 mg per cm² of PE, and these starch coatings imparted hydrophilic properties to film surfaces, as evidenced by contact angle measurements. Although starch could be removed by gently rubbing water‐wet PE surfaces, air‐dried coatings were more firmly attached, and did not separate from the PE surface when films were bent or flexed. SEM images of starch‐coated film surfaces showed that starch was deposited as particles less than 1 μm in diameter, and also as aggregates of these submicron particles. Despite the fact that some starch samples contained only very small amounts of amylose and native lipid, surface‐deposited starch in all experiments contained 90–100% amylose; and exhibited the same V_h X‐ray diffraction pattern, indicative of helical inclusion complex formation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1781–1788, 2002; DOI 10.1002/app.10589     

Design of responsive double-hydrophilic A-b-(B-co-C) diblock terpolymers with tunable thermosensitivity

Double-hydrophilic poly[(oligo(ethylene glycol) methacrylate)-co-methyl methacrylate]-b-poly(2-(diethylamino)ethyl methacrylate), P(EGMA-co-MMA)-b-PDEA, diblock terpolymers were designed and explored in aqueous media. Thanks to the thermosensitivity of the P(EGMA-co-MMA) statistical block and the pH sensitivity of the PDEA block, these terpolymers form two distinct micellar self-assemblies at different conditions of pH and temperature. The thermosensitivity of these terpolymers can be tuned by controlling the LCST of the statistical block through its monomer unit composition.     

Surface‐initiated atom transfer radical polymerization from Mg(OH)2 nanoparticles to prepare the well‐defined polymer‐Mg(OH)2 nanocomposites

Well‐defined polymer‐Mg(OH)₂ nanocomposites were prepared by atom transfer radical polymerization (ATRP). The ATRP initiators were covalently attached to the Mg(OH)₂ by esterification of 2‐chloropropionyl chloride with hydroxyl group. The amount of polymer grafted from Mg(OH)₂ can be controlled using a different catalyst system and adding a small amount of polar solvent. The well‐defined diblock copolymer, consisting of poly(styrene) (PS) and poly(methyl methacrylate) (PMMA) were synthesized. The products were characterized by nuclear magnetic resonance, Fourier transform infrared, differential scanning calorimetry, and thermal gravimetric analysis. The morphologies of PS/PMMA and PS/PMMA/Mg(OH)₂‐g‐PS‐b‐PMMA blends are compared by using a scanning electron microscope. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3680–3687, 2007     

Effect of dopants on the performance of CuO–CeO2 catalysts in methanol steam reforming

Steam reforming of methanol was carried out over a series of doped CuO–CeO₂ catalysts prepared via the urea–nitrate combustion method. XRD analysis showed that at least part of the dopant cations enter the ceria lattice. The addition of various metal oxide dopants in the catalyst composition affected in a different way the catalytic performance towards H₂ production. Small amounts of oxides of Sm and Zn improved the performance of CuO–CeO₂, while further addition of these oxides caused a decrease in catalyst activity. XPS analysis of Zn- and Sm-doped catalysts showed that increase of dopant loading leads to surface segregation of the dopant and decrease of copper oxide dispersion. The addition of oxides of La, Zr, Mg, Gd, Y or Ca lowered or had no effect on catalytic activity, but led to less CO in the reaction products. Noble-metal modified catalysts had slightly higher activity, but the CO selectivity was also significantly higher.     

A MECHANISTICALLY BASED MATHEMATICAL MODEL OF SULFUR DIOXIDE ABSORPTION INTO A CALCIUM HYDROXIDE SLURRY IN A SPRAY DRYER

A mathematical model has been developed to predict So₂ absorption and removal during the constant rate drying period of a spray dryer. The model, based on film theory, treats the atomized slurry droplets as spheres containing discrete sorbent particles of slaked lime with the fluid uniformly distributed around the individual particles. The model includes gas and liquid phase mass transfer coefficients as well as resistance to Ca(OH)₂ dissolution. A sensitivity analysis has been conducted and a comparison was made between pilot-scale experimental data and model-predicted values of S0₂ removal efficiency.     

Oxygen reduction activity of Pt and Pt-Mn-Co electrocatalysts sputtered on nano-structured thin film support

We report on extensive measurements of oxygen reduction activity of Pt and Pt-Co-Mn electrocatalysts using the rotating ring-disk electrode (RRDE) method. The electrocatalysts were prepared by sputtering from Pt or Pt, Co and Mn targets onto 3M's nano-structured thin film support (NSTF) structures. The area specific activity of Pt/NSTF, measured in 0.1 M HClO₄ and at room temperature, is similar to that of bulk Pt. The area specific measurements show a 20 mV reduction in the Pt-Co-Mn/NSTF overpotential compared to Pt/NSTF. The corresponding kinetic gain in the area specific activity of the ternary alloy is about a factor of two. This ORR enhancement factor observed in the ternary Pt-Co-Mn/NSTF by RRDE measurements is similar to the results obtained in 50 cm² H₂/air fuel cells.     

Cracking and the Indentation Size Effect for Knoop Hardness of Glasses

The Knoop hardnesses of five glasses decreased with increasing load in accordance with the classic indentation size effect (ISE). At moderate loads, cracking dramatically altered the indentation sizes and the ISE trends in three of the five glasses. Cracked indentations were as much as 10 μm longer than uncracked indentations made under identical conditions. Diagonal length readings must be corrected for optical resolution limitations if low power lenses are used.     

ESTIMATION FOR NONNEGATIVE AUTOREGRESSIVE PROCESSES WITH AN UNKNOWN LOCATION PARAMETER

Abstract. Consider an AR(1) process given by X ^t=γ+ø X _t+ Z _t≥ 1. where 0 ≤γ, 0 ≤ø 1 are unknown parameters and the innovations Z _t, ≥ 1, are independently and identically distributed positive random variables. We propose estimates of (γø) which are obtained as the solution to a linear programming problem and establish their strong consistency. When the Z _ts have the exponential distribution. our estimate becomes the conditional maximum likelihood estimate given X ₀. Under the assumption of regular variation of the innovation distribution at its left and right endpoints (assumed to be 0 and ∝ respectively), we establish asymptotic limit laws for the estimates. Consistent estimators for a class of moving-average processes with heavy-tailed innovation distribution are also presented.     

Saponification kinetic study of mica-acrylonitrile graft copolymers

Kinetics of alkaline hydrolysis of mica-acrylonitrile graft copolymers was studied. The dependence of alkali concentration and the time of hydrolysis on the degree of saponification was determined. Chemical and spectroscopical techniques were used to determine the mechanism of hydrolysis.